Valitse autosi: 
Näytetään kaikki tuotteet.
BMW N54 twin turbo motor - Forge Recirculation Valves KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"Developed specifically for BMW’s all-new N54 twin turbo motor, as found in the BMW 135,335 and 535 models. Offering significantly improved reliability over the failure prone OEM diaphragm valves, yet with no change to valve response time." Asennusohjeet: http://www.forgemotorsport.co.uk/media/FMDVN54.pdf . Mahdollinen psotikulu +13.20€. Valmistaja Forge.Autoihin:
Bmw-1-Series-(E82) - 135i
Bmw-3-Series-(E92) - 335i

Citroen DS3 1.6 turbo - Forge Recirculation valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
This Recirculation valve ( quiet in operation ) is for the Citroen DS3 1.6 Turbo engines, that have the electronically controlled bypass valves. It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures that have occurred. The problem is that diaphragm retaining ring is made from very thin plastic that goes brittle with heat cycles, and eventually fails.\r\n\r\nUnfortunately the failure doesn’t always result in a check engine light as the valve can still be blown open by the boost pressure, so you may not be aware that you are losing power due to this. This prevents the diaphragm from sealing This particular failure can also result in the valve falling apart upon removal from the turbo, and in extreme cases, we have heard of bits of plastic entering the turbo resulting in serious damage. Our alternative is a fully engineered solution offering both significantly improved reliability .Our valve is piston based , with no diaphragm to fail, and of all aluminium construction, it replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. The valve has been proved on the VAG scene for many years. The spring is interchangeable for different levels of boost, and the solenoid is plug and play with the wiring harness which is included. Asennus ohjeet: http://www.forgemotorsport.co.uk/media/DS3Valve.pdf . Valmistaja Forge.Autoihin:
Citroen-DS3

Ford Focus ST ja RS - Forge Recirculation ValveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"Designed as a direct replacement for the OEM valve which is prone to failure when the engine has been tuned or had an upgrade to the engine management software. This valve is complete and ready to install with no fitting kit required." Ilmoita tilauksen yhteydessä käytättekö ventiili ST vai RS mallissa.Autoihin:
Ford-Focus RS-Mk 2
Ford-Focus ST225

Forge - 28/34mm - Alloy Piston Ram Closed Loop Dump Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Käy mm. Nissan 200SX (S14) - Nissan Sunny GTi-R . Venttiili 28mm sivutulolla ja 34mm alalähdöllä. Toimitetaan Sinisellä jousella, jolla voidaan korvata suoraan mm. Nissanin vakio By-Pass. FMDVTUN säätösarja käy tämän ventiilin kanssa käytettäväksi. Valmistaja Forge.Autoihin:
Nissan-200SX-S14
Nissan-GTI-R

Forge - 34mm - Piston Ram Closed Loop Dump Valve .KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Käy mm. Mitsubishi EVO 4-9. Venttiili 34mm sivutulolla ja alalähdöllä. Toimitetaan Sinisellä jousella, jolla voidaan korvata suoraan mm. Mitsubishi EVO 4-9 vakio By-Pass. FMDVTUN säätösarja käy tämän ventiilin kanssa käytettäväksi. Valmistaja Forge.Autoihin:
Mitsubishi-Lancer Evolution-IV
Mitsubishi-Lancer Evolution-V
Mitsubishi-Lancer Evolution-VI

Forge - Supersize Valve when only the Biggest will doKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"Specifically designed and engineered to offer extreme flow rate capability, where only the largest valve will do. Often when engines have been tuned by installing larger turbo's , software upgrades, and many other boost increasing modifications, improved turbo response can be achieved by fitting the Forge Supersize valve which has the advantage of a greater internal mass air flow specification utilising an amazing 50mm (2") internal bore and an aerodynamic piston to direct the air through the large 40mm inlet and discharge ports (1 5/8"). Available in machined alloy finish". Mahdollinen postikulu +11.60e. Valmistaja Forge.Autoihin:


Forge 006 Piston Closed Loop Diverter Valve - (Black)KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Made from billet aluminium, this recirculating diverter valve dumps the charge-air back into the air intake system keeping external noise to a minimum. This increases both quicker throttle response and higher clamping load to maintain boost pressure more reliably.\r\nUnlike diaphragm diverter valves, this uses counter balanced springs and a single piston to prevent the valve from leaking air into the intake system at idle. This prevents our diverter valves suffering any of the failures associated with single piston and diaphragm type diverter valves.Autoihin:


Forge 006A Piston Closed Loop Diverter Valve with Adjustable Vacuum Connection - (Polished)KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Made from billet aluminium, this recirculating diverter valve dumps the charge-air back into the air intake system keeping external noise to a minimum. This increases both quicker throttle response and higher clamping load to maintain boost pressure more reliably. Unlike diaphragm diverter valves, this uses counter balanced springs and a single piston to prevent the valve from leaking air into the intake system at idle. This prevents our diverter valves suffering any of the failures associated with single piston and diaphragm type diverter valves.Autoihin:


Forge 007P "New Design" - Black - Adjustable PackKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Sarjassa mukana Musta FMCL007P, asennusklemmarit (2 kpl), säätöjousisarja ja shimmilautaset pakettihintaan. Markkinajohtaja alumiinimäntäinen ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Porsche
Saab
Seat
Skoda
VW

Forge 007P "New Design" - Black - AsennusklemmareillaKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. Sarjassa mukana Musta FMCL007P ja asennusklemmarit (2 kpl) pakettihintaan. Markkinajohtaja alumiinimäntäinen ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Porsche
Saab
Seat
Skoda
VW

Forge 007P "New Design" - Black - Fast Road Closed Loop Diverter Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. "New design 007" ja metallimäntäinen, markkinajohtaja ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Porsche
Saab
Seat
Skoda
VW

Forge 007P "New Design" - Machine finish - Adjustable PackKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. Sarjassa mukana Machine finish FMCL007P, asennusklemmarit (2 kpl), säätöjousisarja ja shimmilautaset pakettihintaan. Markkinajohtaja alumiinimäntäinen ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Porsche
Saab
Seat
Skoda
VW

Forge 007P "New Design" - Machine finish - AsennusklemmareillaKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. Sarjassa mukana Machine finish FMCL007P ja asennusklemmarit (2 kpl) pakettihintaan. Markkinajohtaja alumiinimäntäinen ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Porsche
Saab
Seat
Skoda
VW

Forge 007P "New Design" - Machine finish - Fast Road Closed Loop Diverter ValveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. "New design 007" ja metallimäntäinen, markkinajohtaja ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Porsche
Saab
Seat
Skoda
VW

Forge 007PA - ByPass-venttiili kääntyvällä alipaineliittimellä - PolishedKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. Alipaineliitin kääntyy 360-astetta. Metallimäntäinen ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on ikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Mahdolliset postikulut +11.60€. Valmistaja Forge.Autoihin:
Audi
Saab
Seat
Skoda
VW

Forge 007PAB - ByPass-venttiili kääntyvällä alipaineliittimellä - BlackKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. Alipaineliitin kääntyy 360-astetta. Metallimäntäinen ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on ikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Mahdolliset postikulut +11.60€. Valmistaja Forge.Autoihin:
Audi
Saab
Seat
Skoda
VW

Forge 008 - Black - Turbo Recirculation ValveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. Mukana 2 kpl säätöjousia, shimmilautaset ja Forge-avaimenperä. Metallimäntäinen, markkinajohtaja ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Ford-Focus RS-Mk 1
Porsche
Saab-9-3
Saab-9-5 (vm.- 2010)
Saab-9000
Saab-900
Seat
Skoda
VW

Forge 008 - Gunmetal - Turbo Recirculation ValveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
25mm tulolla/lähdöllä. Mukana 2 kpl säätöjousia, shimmilautaset ja Forge-avaimenperä. Metallimäntäinen, markkinajohtaja ByPass-venttiili, joka korvaa alkuperäisen Boschin tekemän kumikalvoisen version. Tuotteella on elinikuinen takuu ja kestää ongelmitta virityksen tuoman lisärasituksen. Valmistaja Forge.Autoihin:
Audi
Ford-Focus RS-Mk 1
Porsche
Renault -Clio
Saab-9-3
Saab-9-5 (vm.- 2010)
Saab-9000
Saab-900
Seat
Skoda
VW

Forge Diverter / BOV Tuning KitKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Optimaalista tulosta Forgen ventiilistä etsivälle valmis tunig-kit. Sarjassa Neljä jousta ja kolme spaceriä. Sarjassa englaninkieliset ohjeet mukana. Punainen on jäykin (tarkoitettu yli 2 bar), sininen (tarkoitettu 1.5-2 bar) seuraavaksi jäykin sitten keltainen (tarkoitettu 1-1.5 bar ahdoille) ja löysimpänä vihreänvärinen jousi (tarkoitettu 0.3-1 bar ahdoille). Valmistaja Forge.Autoihin:


Forge DVRSR - 25mm - Polished - Recirculating-venttiili KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
The Forge RS valve has been specifically designed and engineered, to offer extreme flow rate capability, where other valves are just not up to it. Often when engines have been tuned by installing larger turbos or even software upgrades improved turbo response can be acheived by fitting the RS valve which has the greater internal mass air flow specification utilising an amazing 50mm (2") bore. For fine tuning there is a variable spring preload incorporated and a ratchet type top adjuster that will allow for the positive and precise adjustment that your driving style demands. To ease installation a 360 degree adjustable vacuum hose connector With a choice of inlet and outlet connections the RS valve can be matched to your engine perfectly This valve incorporates a unique conical, progressive rate spring that can allow for the retention of boost pressure from 7 to 34 PSI depending on the individual user's application and level of adjustment. 50mm männällä. Jousensäätö ventiilin päällä. Vaihdettavat letkun kiinnikeet. Alipaineliitin kääntyy 360-astetta. Valmistaja Forge.Autoihin:
Audi
Porsche
Saab
Seat
Skoda
VW

Forge DVRSR - 34mm - Polished - Recirculating-venttiili KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
The Forge RS valve has been specifically designed and engineered, to offer extreme flow rate capability, where other valves are just not up to it. Often when engines have been tuned by installing larger turbos or even software upgrades improved turbo response can be acheived by fitting the RS valve which has the greater internal mass air flow specification utilising an amazing 50mm (2\") bore. For fine tuning there is a variable spring preload incorporated and a ratchet type top adjuster that will allow for the positive and precise adjustment that your driving style demands. To ease installation a 360 degree adjustable vacuum hose connector With a choice of inlet and outlet connections the RS valve can be matched to your engine perfectly This valve incorporates a unique conical, progressive rate spring that can allow for the retention of boost pressure from 7 to 34 PSI depending on the individual user\'s application and level of adjustment. 50mm männällä. Jousensäätö ventiilin päällä. Vaihdettavat letkun kiinnikeet. Alipaineliitin kääntyy 360-astetta. Valmistaja Forge.Autoihin:


Forge SPLIT-R - Black - AsennusklemmareillaKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Väriltään musta paketti sisältää myös asennusklemmarit (2 kpl). 20-30% Blow-off-Bypass yhdistelmä ventiili mm. VAG:n 1.8T koneisiin. Sarjassa mukana myös sokkolautanen normaaliin By-pass käyttöön. The SPLIT-R valve which has been specifically designed for the VAG 1.8T engines to allow a combined recirculation and blow off action resulting in a wonderful sound.". Ventiilin asennus- ja säätöohjeet: http://www.forgemotorsport.co.uk/media/USASPLTR.pdf . Valmistaja Forge.Autoihin:
Audi
Seat
Skoda
VW

Forge SPLIT-R - Black - The Splitter Recirculation and Blow Off Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Väriltään musta. 20-30% Blow-off-Bypass yhdistelmä ventiili mm. VAG:n 1.8T koneisiin. Sarjassa mukana myös sokkolautanen normaaliin By-pass käyttöön. The SPLIT-R valve which has been specifically designed for the VAG 1.8T engines to allow a combined recirculation and blow off action resulting in a wonderful sound.". Ventiilin asennus- ja säätöohjeet: http://www.forgemotorsport.co.uk/media/USASPLTR.pdf . Valmistaja Forge.Autoihin:
Audi
Seat
Skoda
VW

Forge SPLIT-R - Machine finish - AsennusklemmareillaKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Alumiinin värinen ja paketti sisältää myös asennusklemmarit (2 kpl). 20-30% Blow-off-Bypass yhdistelmä ventiili mm. VAG:n 1.8T koneisiin. Sarjassa mukana myös sokkolautanen normaaliin By-pass käyttöön. The SPLIT-R valve which has been specifically designed for the VAG 1.8T engines to allow a combined recirculation and blow off action resulting in a wonderful sound.". Ventiilin asennus- ja säätöohjeet: http://www.forgemotorsport.co.uk/media/USASPLTR.pdf . Valmistaja Forge.Autoihin:


Forge SPLIT-R - Machine finish - The Splitter Recirculation and Blow Off Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Alumiinin värinen. 20-30% Blow-off-Bypass yhdistelmä ventiili mm. VAG:n 1.8T koneisiin. Sarjassa mukana myös sokkolautanen normaaliin By-pass käyttöön. The SPLIT-R valve which has been specifically designed for the VAG 1.8T engines to allow a combined recirculation and blow off action resulting in a wonderful sound." Ventiilin asennus- ja säätöohjeet: http://www.forgemotorsport.co.uk/media/USASPLTR.pdf . Valmistaja Forge.Autoihin:
Audi
Seat
Skoda
VW

Garrett Turbo T25 - Forge Recirculation Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Käy autoihin jossa Garrett T25 turbo. Näitä ahtimia löytyy mm Saab, Renault 225 Megane, Rover 220/420/620/820, MG ZT, Escort Cosworth. Autoihin:
Ford-Sierra
Renault
Saab

Mazda MPS 3/6 & CX-7 (Legacy BP/BL) - Black - Forge Recirculation Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
A flange mounting Piston Recirculation Valve suitable for the Legacy BP/BL and Maxdaspeed 3 or 6 & CX-7 SUV. Valmistaja ForgeAutoihin:
Mazda-CX-7
Mazda-MPS 3
Mazda-MPS 6

Mazda MPS 3/6 & CX-7 (Legacy BP/BL) - Polished - Forge Recirculation Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
A flange mounting Piston Recirculation Valve suitable for the Legacy BP/BL and Maxdaspeed 3 or 6 & CX-7 SUV. Valmistaja ForgeAutoihin:
Mazda-CX-7
Mazda-MPS 3
Mazda-MPS 6

Mini Cooper S Turbo - Forge uprated valveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures that have occurred. The most common complaint on the OEM solenoid valve is a split diaphragm preventing the valve from opening fully, or not at all. This doesn’t always result in a check engine light as the valve can still be blown open by the boost pressure. We have seen many valves with this problem (see image below). The other problem is that diaphragm retaining ring is made from very thin plastic that goes brittle with heat cycles, and eventually fails. This prevents the diaphragm from sealing with the same problems as mentioned above. This particular failure also results in the valve falling apart upon removal from the turbo, though in extreme cases bits of plastic can enter the turbo and destroy it. (see image below). Our alternative is a fully engineered solution offering both significantly improved reliability .Our valve is piston based , with no diaphragm to fail, and of all aluminium construction, it replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. The valve has been proved on the VAG scene for many years. The spring is interchangeable for different levels of boost, and the solenoid is plug and play with the wiring harness which is included. Autoihin:
Mini -Cooper-S 1.6i Turbo
Mini -Cooper-S Clubman 1.6i Turbo

Mitsubishi TD - Forge Recirculation Valve - "New design" KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
HUOM. Uusi alumiinimäntäinen By-pass. käymm. Volvo X40 (Mitsubishi TD04HL1-12T /14T). Vakio ventiilin tilalle tuleva paremmin kestävä. Käy suurimpaan osaan mm. Volvon käyttämiin Mitsun ahtimiin. "The Forge recirculation valve is ideal for upgrading or replacing the factory original valve, without the need for changing the whole turbo assembly on vehicles using the Mitsubishi TD series turbochargers. A good cost efective modification on any Volvo,Renault or Hyundai with this type of valve." Valmistaja Forge.Autoihin:
Hyundai
Renault -Megane-225 2.0T (vm.2004-)
Renault -Megane-230 F1 Team R26 (vm.2006-)
Renault -Megane-230 F1 team R26R (vm.2006-)
Volvo-S/V40 - (vm.1995-2004)-2.0T-Fas 1
Volvo-S/V40 - (vm.1995-2004)-2.0T-Fas 2
Volvo-S/V40 - (vm.1995-2004)-T4-Fas 1
Volvo-S/V40 - (vm.1995-2004)-T4-Fas 2

Nissan GT R35 - Forge Recirculation Valves KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"These valves are a direct replacement for the (OEM) original valves. They offer significantly higher flow rate capability, where other valves are just not up to it. This is achieved by utilising an amazing 50mm (2") bore. For fine tuning there is a variable spring preload incorporated and a ratchet type top adjuster that will allow for the positive and precise adjustment . This valve incorporates a unique conical, progressive rate spring that can allow for the retention of boost pressure up to 34 PSI. To ease installation there is a 360 degree adjustable vacuum hose connector ." mahdollinen postikulu +13.20€. Valmistaja Forge.Autoihin:
Nissan-GT-R R35

Nissan Juke 1.6 Turbo - Forge Recirculation ValveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
" A fully engineered piston type, turbocharger recirculation valve for the Nissan Juke 1.6 Turbo.\r\nThe design and materials used in the construction of this valve enable not only for the valve to be tuned when boost pressures have been increased but even on a standard car will provide a fast acting and responsive valve that gives reliability over failures often associated with the original manufacturers design." Valmistaja Forge.Autoihin:
Nissan-Juke-1.6 Turbo

Opel - Forge Recirculation valveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Käy mm. Opel Astra G or H type Z20LET, Corsa VXR 1.6 Turbo Z16LER ja Zafira A or B with Z20LET. "Designed as a direct replacement for the OEM valve which is prone to failure when the engine has been tuned or had an upgrade to the engine management software. This valve is supplied assembled with our "green" coded spring which is suitable for standard or mildly tuned engines. This valve is complete and ready to install with no fitting kit required." Valmistaja Forge.Autoihin:
Opel-Astra H-2.0T 240hp
Opel-Corsa-1.6T OPC 192hp
Opel-Zafira-OPC

Peugeot 207/307/308 GT Turbo - Forge uprated valveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Peugeot 207/307/308 GT Turbo it is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures that have occurred. The most common complaint on the OEM solenoid valve is a split diaphragm preventing the valve from opening fully, or not at all. This doesn’t always result in a check engine light as the valve can still be blown open by the boost pressure. We have seen many valves with this problem (see image below). The other problem is that diaphragm retaining ring is made from very thin plastic that goes brittle with heat cycles, and eventually fails. This prevents the diaphragm from sealing with the same problems as mentioned above. This particular failure also results in the valve falling apart upon removal from the turbo, though in extreme cases bits of plastic can enter the turbo and destroy it. (see image below). Our alternative is a fully engineered solution offering both significantly improved reliability .Our valve is piston based , with no diaphragm to fail, and of all aluminium construction, it replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. The valve has been proved on the VAG scene for many years. The spring is interchangeable for different levels of boost, and the solenoid is plug and play with the wiring harness which is included. Autoihin:
Peugeot-207

Porsche 996 - Forge - (Alumiini) - Fast Road Closed Loop Diverter Valve with Adjustable Vacuum ConnectionKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Alumiininvärisillä ventiileillä. sis. auton vaatima 2 kpl !!! Made from billet aluminium, this recirculating diverter valve dumps the charge-air back into the air intake system keeping external noise to a minimum. This increases both quicker throttle response and higher clamping load to maintain boost pressure more reliably. Flush Fit Valve option. Where there are space limitations, or a side vacuum pipe connection is required, we can offer a replacement giving a 360º option for the vacuum pipe positioning. These valves are especially useful on Porsche turbo installations or where engine covers restrictions are present. Valmistaja Forge.Autoihin:
Porsche-955 - Cayenne Turbo
Porsche-996 - GT 2
Porsche-996 - Twin Turbo S
Porsche-996 - Twin Turbo

Porsche 996 - Forge - (Musta) - Fast Road Closed Loop Diverter Valve with Adjustable Vacuum ConnectionKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Mustilla ventiileillä. sis. auton vaatima 2 kpl !!! Made from billet aluminium, this recirculating diverter valve dumps the charge-air back into the air intake system keeping external noise to a minimum. This increases both quicker throttle response and higher clamping load to maintain boost pressure more reliably. Flush Fit Valve option. Where there are space limitations, or a side vacuum pipe connection is required, we can offer a replacement giving a 360º option for the vacuum pipe positioning. These valves are especially useful on Porsche turbo installations or where engine covers restrictions are present. Valmistaja Forge.Autoihin:
Porsche-955 - Cayenne Turbo
Porsche-996 - GT 2
Porsche-996 - Twin Turbo S
Porsche-996 - Twin Turbo

Porsche 996 - Forge Recirculation valve kit KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Saatavana mustalla, punaisella tai mustalla letkulla. "Following the resounding success of our direct replacement valves for other OEM applications, we have just completed development and testing of a pair of direct replacement bypass valves specific to the Porsche 996 twin turbo application. These direct replacement units utilize full billet aluminum construction and a piston based design that has proved successful throughout our entire range of application specific and universal valve products. Viton brand high temp silicone o-ring are used for sealing of the piston and the valve cap, Mobil1 fully synthetic bearing grease for lubrication of the internals, and a proprietary spring rate is used to handle the widest possible range of boost pressures. The low-profile cap incorporates a swiveling center section that allows for 360 rotation of the vacuum nipple for ease of fitment. This also allows for quick disassembly of the valve without requiring removal from the vehicle should servicing of the internals be required. In addition we supply a replacement silicone hose that is capable of withstanding greater temperatures and pressures, often associated with tuned or track use vehicles." Valmistaja Forge.Autoihin:
Porsche-996 - Twin Turbo

Porsche 997 Turbo - Forge Pair of Piston Valves KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"Following the resounding success of our direct replacement valves for other OEM applications utilizing Borg Warner triple-K series turbochargers, we have just completed development and testing of a pair of direct replacement bypass valves specific to the Porsche 997 twin turbo application. These direct replacement units utilize full billet aluminum construction and a piston based design that has proved successful throughout our entire range of application specific and universal valve products. Viton brand high temp silicone o-ring are used for sealing of the piston and the valve cap, Mobil1 fully synthetic bearing grease for lubrication of the internals, and a proprietary spring rate is used to handle the widest possible range of boost pressures. The low-profile cap incorporates a knurled outer ring and a swiveling center section that allows for 360 rotation of the vacuum nipple for ease of fitment. This also allows for quick disassembly of the valve without requiring removal from the vehicle should servicing of the internals be required." Valmistaja ForgeAutoihin:
Porsche-997.1 - GT 3
Porsche-997.1 - Twin Turbo

Subaru Impreza (vm.2008-) - WRX - Forge Recirculation Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"A direct bolt on replacement Recirculation valve for the new 2008 Subaru Impreza WRX with either the 2.0 litre or 2.5 litre engines." HUOM. ei käy STI-maliin !! Mahdolliset postikulut +11.60€. Valmistaja Forge. Autoihin:
Subaru-Impreza-2.5T WRX vm.2008-

Subaru Impreza - Forge Recirculation valveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Tarkoitettu korvaamaan vakio takaisinkiertoventiilin. Käy autoihin esim. Mazda RX7, Toyota Supra ja Subaru Impreza vm.1993-95. Valmistaja Forge.Autoihin:


Subaru Impreza MY 01 - Forge Piston Recirculating ValveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Alloy Recirculating Valve available to fit the Impreza 2001 onwards models including the 2009 GR STi Made from billet aluminium, this recirculating diverter valve dumps the charge-air back into the air intake system keeping external noise to a minimum. This increases both quicker throttle response and higher clamping load to maintain boost pressure more reliably. Mahdollinen postikulu +11.60€. Valmistaja Forge.Autoihin:
Subaru-Forester vm.2001-
Subaru-Impreza-2.0T STI vm.2001-2007
Subaru-Impreza-2.0T WRX vm.2001-2007
Subaru-Impreza-2.5T STI vm.2005-2008
Subaru-Impreza-2.5T WRX vm.2005-2008

Subaru Impreza V5 - Forge Piston Ram Closed Loop Dump Valve (Flange Mounted) KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
Alumiininen kierrättävä Piston Ram Closed Loop Dump Valve, laippaan kiinnitettävä! Subaru Impreza V5-malleihin. Mahdollinen postikulu +11.60€. Valmistaja Forge.Autoihin:
Subaru-Impreza-2.0T STI vm.1994-2001
Subaru-Impreza-2.0T STI vm.2001-2007
Subaru-Impreza-2.0T WRX vm.1994-2001
Subaru-Impreza-2.0T WRX vm.2001-2007

VAG 1.4 TSi Twincharged engines - Forge Recirculation Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
This valve kit is for VAG vehicles equipped with the 1.4 Tsi twincharged ( supercharged and turbocharged ) engines that have the electronically controlled bypass valves ( 2 bolt fitting). It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures of the OEM valve, that have occurred. Our alternative is a fully engineered solution offering both significantly improved reliability. Our valve and installation kit replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. This product has been thoroughly designed and tested with the expressed intent of offering improved valve response and maintaining ECU control while resulting in absolutely NO fault codes, NO check engine lights, and no adverse effects of any kind. All of the necessary components and detailed instructions are included and everything is designed to make installation as simple as possible.Autoihin:
Audi
Seat
Skoda
VW

VAG 1.4 Turbo engines - Forge Recirculation Valve KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
This valve is for VAG vehicles equipped with the 1.4TFSI that have the electronically controlled bypass valves. It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles fitted with the earlier version of the OEM valve that operate in warmer climates, as a solution to the many failures of the diaphragm that have occurred. This WILL NOT fit 2011 vehicles with the IHI turbo !! Valmistaja Forge.Autoihin:
Audi
Seat
Skoda
VW

VAG 1.8 ja 2.0TSI - Replacement Vacuum operated ValveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"world’s first fully engineered solution offering both significantly improved reliability as well as valve related boost response. Our valve and installation kit replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. This product has been thoroughly designed and tested with the expressed intent of offering improved valve response and maintaining ECU control while resulting in absolutely NO fault codes, NO check engine lights, and no adverse effects of any kind. All of the necessary components and detailed instructions are included and everything is designed to make installation as simple as possible. " Valmistaja Forge.Autoihin:
Audi
Seat
Skoda
VW

VAG 2.0TFSI - Replacement Valve Engines with remotely located valves KLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
"If you are running increased boost pressures, after a software remap (chip), or the OEM valve is being subjected to high temperatures, the lifespan of the unit is significantly reduced. Even without any modifications taking place to the vehicle at all, this OEM valve has been shown to fail over time and it’s boost holding capacity also leaves some room for improvement. Our alternative is a fully engineered solution offering both significantly improved reliability as well as valve related boost response. Our valve and installation kit replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation. This product has been thoroughly designed and tested with the expressed intent of offering improved valve response and maintaining ECU control while resulting in absolutely NO fault codes, NO check engine lights, and no adverse effects of any kind. All of the necessary components and detailed instructions are included and everything is designed to make installation as simple as possible." Valmistaja Forge.Autoihin:
Audi
Seat
Skoda
VW

Volvo T5 - Forge Recirculation valveKLIKKAA TÄSTÄ JA KATSO HINTA UUSILTA SIVUILTAMME!
käy mm Volvo 2004.5 - 2010 S40, Volvo V50 T5 (FWD/AWD), Volvo vm. 2006 - 2010 C70 II T5, Volvo vm. 2007 - 2010 C30 T5, Volvo vm.2004 - 2007, S60R/V70R, Volvo vm. 2005 and up S60 T5. This is a piston design recirculation valve that is a direct replacement for the original fitment. This valve gives greater longevity than the diaphragm (OEM) valves but also benefits from its ability to be fitted with different springs when the boost pressure has been increasded or the engine has been modified. To ease installation the top or vacuum connection is angled. Autoihin:
Volvo-C30-T5 220hp
Volvo-V70N (vm.2000-2007)-T5


copyright 2002-2011, Doc Power Oy varaa oikeuden hinnanmuutoksiin ilman erillistä ilmoitusta